Dubai,UAE
Office Address
info@alkaramatechnical.com
Email Address
Menu
Office Address
Email Address
Coil, ceramic & induction hobs · Same-day across Dubai
A burner that won’t heat, a hob that trips the power, touch controls that don’t respond, or a crack across the glass? Al Karama Technical LLC sends a trained technician to your home or kitchen anywhere in Dubai, usually the same day. We test before we replace anything, give you a fixed price first, and fix most electric stoves in a single visit.
Al Karama Technical LLC repairs electric stoves of every type across Dubai: coil and solid-plate burners, ceramic glass hobs, induction hobs and electric cookers. A technician usually visits the same day, or you can bring a portable hotplate or single induction cooker to our workshop in Al Karama. Most repairs take 1 to 2 hours: heating elements, burner switches, touch control boards, sensors and hob glass. Every job ends with an electrical safety check.
Most Dubai apartments are built with an electric hob, usually a ceramic or induction glass top set into the worktop. They’re clean and easy to use, but when one zone stops heating or the whole hob goes dead, cooking at home stops with it.
If you’re searching for electric stove repair near me, our technicians cover every part of Dubai and carry the parts that fail most: heating elements, energy regulators, burner switches, sensors, terminal blocks and control boards. Since 2015 we’ve repaired everything from single-plate hotplates to five-zone induction hobs and commercial electric ranges.
Electric stoves run on a high-current supply, so we isolate the power, test each circuit properly and never guess with parts.
Each type heats differently and fails differently, so the repair starts with knowing which one you have.
Exposed spiral elements or cast-iron plates. Simple and tough, usually fixed by replacing the element, socket or switch.
Radiant elements under smooth glass. Common faults are a failed element, limiter or cracked glass.
Heat the pan directly with a magnetic field. Faults are usually electronic: boards, coils, sensors or fans.
Freestanding cookers with an electric hob and oven, including commercial ranges.
These are the faults we see most on electric stoves in Dubai, what usually causes them, and how we repair them.
| Problem | Most likely cause | How we fix it |
|---|---|---|
| One burner or zone not heating | Burnt-out element, loose connection, failed switch or energy regulator | Test and replace the element, repair the connection, fit a new switch |
| Burner stuck on full heat | Faulty energy regulator (infinite switch) | Replace the regulator for that zone |
| Whole hob dead | Tripped breaker, isolator off, burnt terminal block, failed power board | Check the supply, replace the terminal block or power board |
| Hob trips the breaker | Element shorting to earth, moisture under the glass, damaged wiring | Insulation test, replace the faulty element or wiring |
| Touch controls not responding | Wet or dirty panel, child lock on, failed touch control board | Clean and reset, or replace the touch board |
| Cracked or chipped glass | Impact, or a hot pan on a weak spot | Replace the glass top. Don't use the hob until it's done |
| Induction zone won't detect the pan | Pan isn't magnetic or is too small, or a faulty coil or sensor | Check the cookware, then test the coil, sensor and board |
| Induction hob cuts out or shows an error | Overheating from a blocked fan or vent, or a sensor or board fault | Clean the fan and vents, test sensors, repair the board |
| Coil sparks or glows unevenly | Damaged element or burnt socket | Replace the coil and its socket |
| Indicator light stays on | Stuck switch or a residual-heat sensor fault | Replace the switch or sensor |
When one burner stops working and the others are fine, the fault is nearly always in that burner’s own circuit. Our electric stove burner repair covers each part of it:
We test each part with a meter, so you pay for the one that has actually failed and not a set of parts fitted in hope.
Induction hobs confuse a lot of people the first time they use one. There’s no element heating up. The hob creates a magnetic field, and the pan itself becomes the hot part. That means a zone will refuse to start if the pan isn’t right, and it looks exactly like a fault.
Before you book a repair, try this. Hold a fridge magnet to the base of the pan. The U.S. Department of Energy notes that any flat-bottomed pan a magnet sticks to will work on an induction cooktop. If the magnet falls off, the pan is the problem. Aluminium, copper and some stainless steel pans won’t work.
If the pan is fine and the hob still misbehaves, these are the real faults we repair:
Induction hobs are well worth repairing. The parts cost far less than a new hob, and a working induction zone heats faster and wastes less energy than any other type.
Tell us the hob type, brand and fault. A photo of the hob or error code helps.
Power isolated, then each element, switch, sensor and board is tested.
You approve the price before any work starts.
We fit the part, test every zone and check the earth and insulation.
If you’re looking for an electric stove repair shop near me, the answer depends on what you own.
Bring it to our workshop. Portable hotplates, single and double induction cookers and small table-top electric stoves are easy to carry. Drop yours at Shop #1, Building G4, Sheikh Hamdan Colony, Al Karama, and we’ll test and repair it on the bench.
Book a home visit. Built-in hobs and electric cookers are wired directly into a high-current cooker circuit and sealed into the worktop. They shouldn’t be disconnected by anyone untrained. A technician comes to you, isolates the supply, lifts the hob safely and repairs it on site.
Need directions? Visit our contact page.
Common parts travel in the van. Model-specific glass tops and control boards are ordered quickly from trusted suppliers.
We repair electric stoves and hobs from all the main brands sold in Dubai:
Call now for a same-day electric stove technician anywhere in Dubai.
It depends on the hob type and the part. A coil element or switch is a small job. Induction boards and glass tops cost more. Our technician diagnoses first and gives you a fixed quote before starting, with no hidden charges.
As a guide, here’s how long common repairs take:
| Repair | Typical time | Notes |
|---|---|---|
| Coil element or socket replacement | 30–45 minutes | Usually done on the first visit |
| Ceramic hob element or limiter | 45–90 minutes | Hob lifted out, element replaced and tested |
| Switch or energy regulator | 30–60 minutes | Fixes burners stuck off or on full |
| Touch control or power board | 1–2 hours | Board may need ordering for some models |
| Induction coil, sensor or fan | 1–2 hours | Includes full zone test afterwards |
| Hob glass replacement | 1–2 hours once the glass arrives | Glass is model-specific and usually ordered |
Repair or replace? Elements, switches, sensors and most boards are well worth repairing. If the glass is cracked on a low-cost hob, compare the glass price with a new hob first. We’ll give you both numbers so you can decide.
Burners, igniters and valves: gas stove repair.
Freestanding gas cookers and ranges: gas cooker repair in Dubai.
Electric, gas and microwave ovens: oven repair in Dubai.
Draining, heating and leak faults: dishwasher repair.
Cooling and freezer faults: fridge repair in Dubai.
See everything we repair for homes and businesses.
Our electric stove repair Dubai team covers the whole city, including Al Karama, Bur Dubai, Deira, Al Qusais, Al Nahda, International City, Mirdif, Business Bay, Downtown Dubai, Jumeirah, Al Barsha, Al Quoz, Dubai Marina, JLT, JVC, Discovery Gardens, Arabian Ranches and Dubai Silicon Oasis.
Our cooking appliance technicians also have local pages for Karama, Bur Dubai and Dubai Marina.
Power isolated, and earth and insulation checked on every job.
Technicians across Dubai, with evening and weekend slots.
Diagnosis first, then a clear quote you approve.
A shop in Al Karama since 2015, not just a phone number.
Straight answers to the questions Dubai customers ask us most about electric stove repair.
It depends on the hob type and the part. Coil elements and switches are small jobs, while induction boards and glass tops cost more. We diagnose first and give you a fixed quote before any work starts.
Usually the heating element for that zone has burnt out, the switch or energy regulator behind the knob has failed, or a connection has come loose. Each is tested with a meter so only the faulty part is replaced.
An element is probably shorting to earth, or moisture has got under the glass. Stop using the hob, switch it off at the cooker isolator and book a repair. Repeated resets can be unsafe.
No. Liquid can pass through the crack and reach live parts underneath. Switch the hob off at the isolator and have the glass replaced before using it again.
Induction only works with magnetic cookware. If a fridge magnet sticks to the base, the pan is suitable. If the pan is fine and the zone still won’t start, the coil, sensor or control board needs testing.
Check the panel is dry and clean and that child lock isn’t on. Switching the hob off at the isolator for a few minutes often resets it. If the controls still don’t respond, the touch board has likely failed.
Most repairs take 1 to 2 hours and are finished in one visit. Glass tops and some control boards are model-specific and may need to be ordered.
Yes. Our workshop is at Shop #1, Building G4, Sheikh Hamdan Colony, Al Karama. Bring portable hotplates and table-top induction cookers to us, or book a home visit anywhere in Dubai for built-in hobs and cookers.
In most cases, yes. Call or WhatsApp early in the day and we can usually send a technician the same day.
All major brands, including Bosch, Siemens, Samsung, LG, Ariston, Whirlpool, Electrolux, AEG, Teka, Elba, Smeg, Miele, Beko, Midea and Haier.
Elements, switches, sensors and most boards are worth repairing. If the glass is cracked on a low-cost hob, replacement can make more sense. We’ll give you both prices.
Yes. Every repair is covered by our workmanship warranty, and we use quality parts suited to your brand.
Proper testing, fixed prices and a safety check on every job. Cooking again, usually the same day you call.